Get a Quote

Our representative will contact you soon.
Email
Message
0/1000
Company Name

News

Home >  News

Aerator Threads and Adaptors: M22 and M24, Male Versus Female, and Retrofitting Flow Restrictors

Nov 22, 2026

Almost every aerator problem starts the same way. Someone measures 24 mm across the spout, orders an M24 aerator, and finds it will not start in the thread. Diameter is only half the answer. The other half is whether the thread sits on the outside of the spout or inside a recess, because "M22 female" and "M24 male" describe the aerator, not the tap.

Get those two facts right and the rest — washers, restrictors, swivel heads — falls into place.

The thread families you will actually meet

Aerator thread Thread location Fits a spout that is Typical application
M22×1 female inside the aerator body 22 mm male (external) Kitchen mixers, many pull-out heads
M24×1 male outside the aerator body 24 mm female (recessed) Basin mixers, some kitchen taps
M28×1 male outside 28 mm female Larger basin and bath spouts
M18.5×1 male outside 18.5 mm female Compact and slim pull-out heads
3/4″ BSP male outside 3/4″ female Older and industrial-style taps

Measuring without guessing

For a male spout, measure across the thread crests with a caliper; the nominal size is the diameter, so 21.8 mm is M22. For a female recess, measure the inside diameter and the depth. Depth catches people out: a deep recess needs a longer aerator body or a dedicated key, while a shallow one will not accept a stacked adaptor without the assembly standing proud of the spout.

Also look at the seat: limescale or corrosion on the shoulder will leak no matter how good the thread is. Clean it first — a five-year-old brass basin mixer usually has a hard scale ring exactly where the washer needs to seal.

Sealing: the shoulder does the work

Threads locate; shoulders seal. An M24 male aerator seals on a flat washer against the base of the recess, and an M22 female aerator seals on a washer against the spout's shoulder. That has two consequences.

First, thread tape is not a fix. Wrapping PTFE around an aerator thread adds thickness to a plastic or thin brass housing and is a reliable way to crack it, and it does nothing for a leak that is passing the washer.

Second, use EPDM or fibre on a flat seat and replace the washer every time the aerator comes off — one that has taken a set will not re-seal. Tighten with a key or coin until the housing stops moving, then stop; snug is the specification, and there is no torque figure worth chasing on a plastic body.

Common adaptor mistakes

  • Buying by diameter alone. A 24 mm measurement fits both an M24 male aerator and an M24 female spout. Check which side carries the thread.
  • Stacking two adaptors. Each joint is another washer and another leak path, and the stack adds 15–25 mm of length that pushes the outlet into the sink or fouls a pull-out head.
  • Assuming M22 is universal. Several makers use proprietary click-fit or bayonet couplings that look like M22 and are not interchangeable.
  • Over-tightening to stop a weep. A weep at the shoulder means a bad or missing washer, not insufficient torque. More force cracks housings and can split a thin spout wall.

Retrofitting a flow restrictor

Restrictors are inserts that sit inside the aerator housing or replace the existing insert. Common ratings are 4, 6 and 8 litres per minute: kitchen taps usually want 8 or above, basin taps 5–6, and commercial installations often lower to meet a water efficiency target.

Two types behave very differently. A fixed orifice restrictor simply passes less water as pressure rises, so at 3 bar it saves a lot and at 0.5 bar it saves almost nothing. A pressure-compensating restrictor holds a near-constant flow across a pressure range, which is what you want on an unsteady mains supply — but on a gravity-fed low-pressure system it can turn a usable tap into a trickle.

Keep the mesh. The restrictor controls flow, the mesh breaks up the jet and stops debris; remove the mesh and the tap spits.

EN 246 is the European specification for flow-rate regulators: it defines flow classes and the test methods used to verify them, which is why a reputable aerator datasheet quotes a class rather than a vague "water saving" claim. The tap it screws into is covered separately by EN 817 for mechanical mixing valves or EN 200 for single taps, and any part in contact with drinking water should carry the approval the destination market expects — WRAS in the UK, NSF/ANSI 61 in North America.

Changing the spray pattern

Dual-flow aerators switch between an aerated stream and a needle spray by twisting the body; swivel aerators add 360° movement for rinsing. Both add height. Before buying, measure the clearance between spout outlet and basin floor, and on a pull-out tap check that the head still docks with the extra length fitted. A swivel that swings into the back of the bowl is worse than none.

Fitting and leak-testing

Isolate the water and open the tap to release pressure.

Unscrew the old aerator with a key or coin; if seized, soften the scale with a warm vinegar soak rather than more force.

Clean the shoulder and the thread, then flush the spout for a few seconds.

Fit a new washer, then the aerator or adaptor, hand-tight.

Open the tap slowly at low flow and check the shoulder with dry tissue.

Run full flow for a minute, then switch the tap off and on ten times.

Re-check after 24 hours; a seal that is going to fail usually weeps on the first hot cycle.

If water appears at the thread rather than the shoulder, stop — the washer is misaligned or the wrong gender was supplied. Neither problem improves with tightening.

Buy by gender and diameter, seal on the shoulder, finish at snug. That covers most of the aerator failures we see returned.

---

About the author

Zhejiang Xindong Sanitary Ware Co., Ltd. is an OEM/ODM manufacturer of kitchen mixer taps and brass basin mixers based in Yuhuan, Zhejiang, China. The company supplies pull-out kitchen mixers, including the T1029N in brushed nickel, and brass basin mixers with standard M22 and M24 aerator threads for importers and private-label brands.

Contact: [email protected] | +86-0576-87499008 | https://www.cn-xindong.com

aerator threads and adaptors m22 and m24 male versus female and retrofitting flow restrictors-0